【摘要】：基于Attaf和Jha等提出的理論,在Oliver-Pharr(OP)法計算壓痕硬度的基礎上,分別建立了卸載功、卸載斜率和壓痕硬度之間的解析模型;用此模型計算得到了壓痕硬度并與面積法計算的結果進行了對比分析,分析了卸載斜率和卸載功的計算誤差對壓痕硬度的影響。結果表明:卸載斜率的計算精度受數據采集誤差的影響較大,以卸載功計算壓痕硬度則可避免數據采集誤差的影響;與OP法相比,以卸載功計算的壓痕硬度與面積法得到的更為接近;卸載斜率計算誤差對壓痕硬度計算精度的影響大于卸載功計算誤差的。
[Abstract]:Based on the theory proposed by Attaf and Jha, the analytical models between unloading work, unloading slope and indentation hardness are established on the basis of Oliver-Pharr (OP) method. The indentation hardness is calculated by this model and compared with the results calculated by the area method. The influence of the unloading slope and the calculation error of the unloading work on the indentation hardness is analyzed. The results show that the accuracy of unloading slope is greatly affected by the error of data acquisition, and the calculation of indentation hardness by unloading work can avoid the influence of data acquisition error. Compared with the OP method, the indentation hardness calculated by the unloading work is closer to that obtained by the area method, and the influence of the error of the unloading slope calculation on the precision of the indentation hardness calculation is greater than that of the unload work calculation error.
【作者單位】： 湖北汽車工業學院機械工程學院;
【基金】：湖北省自然科學基金資助項目(2014CFB623) 湖北汽車工業學院博士基金資助項目(BK201303)
【分類號】：TB302.3

【相似文獻】

相關期刊論文 前10條

1 劉美華,王靜,王東愛;對壓痕硬度試驗方法的分析研究[J];工程塑料應用;2005年07期

2 劉美華;李鴻琦;計宏偉;佟景偉;;壓痕硬度測試法的主要研究內容及其應用[J];理化檢驗(物理分冊);2008年09期

3 金宏平;陳建國;;基于能量法計算材料的彈性模量和壓痕硬度[J];機械工程材料;2013年09期

4 閆薇;安然;趙正;田衛東;朱一辛;;水杉的壓痕硬度與壓痕蠕變特性[J];木材加工機械;2013年05期

5 孫淵;王慶明;;壓痕硬度測試的有限元分析[J];華東理工大學學報(自然科學版);2007年06期

6 楊輝,錢林茂,朱e，

本文編號：2427153