基于ZigBee技術的礦井通風參數測試技術研究與應用設計
發布時間:2018-07-14 20:33
【摘要】:本文針對傳統的通風阻力測量方法的不足,首次提出并設計了一種基于無線通信技術并將現代測量技術、傳感技術和嵌入式技術相結合的無線通信礦用通風多參數測定儀器,通過一組儀器同時測量一段巷道內相距一定距離的兩點的溫濕度和氣壓,,并在一個主儀器上同時顯示。 本文詳細介紹并分析了基于ZigBee無線通信技術的礦井通風多參數測定儀的硬件和軟件的設計原理和實現方法,核心控制處理器件采用了集51單片機和RF射頻技術于一體的ZigBee芯片CC2530,溫濕度采集器件采用SHT10,通過MAX232實現與PC機的數據通信。軟件方面的通信模式采用Z-tack協議棧,以C程序語言為基礎編寫控制與處理程序。
[Abstract]:Aiming at the shortage of traditional ventilation resistance measurement method, this paper presents and designs a wireless communication mine ventilation multi-parameter measuring instrument based on wireless communication technology and combining modern measurement technology, sensor technology and embedded technology. The temperature, humidity and air pressure of two points in a certain distance are measured simultaneously by a group of instruments and displayed on a main instrument at the same time. This paper introduces and analyzes the design principle and realization method of hardware and software of mine ventilation multi-parameter measuring instrument based on ZigBee wireless communication technology. The core control device adopts ZigBee chip CC2530 which integrates 51 single chip computer and RF radio frequency technology, and SHT10 for temperature and humidity collector, and realizes data communication with PC through MAX232. The communication mode of software is Z-tack protocol stack, and the control and processing program is written on the basis of C program language.
【學位授予單位】:遼寧工程技術大學
【學位級別】:碩士
【學位授予年份】:2013
【分類號】:TD724
本文編號:2122868
[Abstract]:Aiming at the shortage of traditional ventilation resistance measurement method, this paper presents and designs a wireless communication mine ventilation multi-parameter measuring instrument based on wireless communication technology and combining modern measurement technology, sensor technology and embedded technology. The temperature, humidity and air pressure of two points in a certain distance are measured simultaneously by a group of instruments and displayed on a main instrument at the same time. This paper introduces and analyzes the design principle and realization method of hardware and software of mine ventilation multi-parameter measuring instrument based on ZigBee wireless communication technology. The core control device adopts ZigBee chip CC2530 which integrates 51 single chip computer and RF radio frequency technology, and SHT10 for temperature and humidity collector, and realizes data communication with PC through MAX232. The communication mode of software is Z-tack protocol stack, and the control and processing program is written on the basis of C program language.
【學位授予單位】:遼寧工程技術大學
【學位級別】:碩士
【學位授予年份】:2013
【分類號】:TD724
【參考文獻】
相關期刊論文 前10條
1 趙佐平;施惠昌;田金鵬;蔣敏;;基于CC2420的井下無線定位方案設計與研究[J];傳感器與微系統;2008年02期
2 王俊彩;王福平;侯瑞峰;王成;;基于BMP085的一種便攜式海拔高度測量系統設計[J];傳感器與微系統;2011年12期
3 雷巍;鄭麗婭;賴文娟;;基于DS1302的時鐘接口設計[J];四川兵工學報;2011年11期
4 楊文鉑;尤一鳴;;基于MC13192的Zigbee無線數傳模塊設計[J];單片機與嵌入式系統應用;2008年01期
5 吳國宏;;新型溫濕度傳感器SHT10的原理及應用[J];單片機與嵌入式系統應用;2009年04期
6 李志方;鐘洪聲;;IEEE802.15.4的CC2530無線數據收發設計[J];單片機與嵌入式系統應用;2011年07期
7 王瑋;樊則賓;;基于CC2430的無線溫度檢測終端的設計[J];電子工程師;2007年08期
8 王樹剛,劉樹存;氣壓計基點法測礦井通風阻力的分析[J];煤炭工程師;1997年06期
9 劉殿武;利用風門測量巷道通風阻力[J];礦業安全與環保;2004年05期
10 周述峰;陶干強;曹偉;宋麗霞;;基于運籌學的礦山通風系統分析[J];金屬礦山;2008年10期
本文編號:2122868
本文鏈接:http://sikaile.net/kejilunwen/anquangongcheng/2122868.html
最近更新
教材專著