發布時間：2018-10-16 13:05

【摘要】：短樁承臺式基礎是一種上部為開挖式基礎、下部為短樁并且考慮共同受力的新型基礎型式。在樁基設計的過程中,通過考慮承臺下地基土反力,應用短樁優化樁基設計,從而使得樁基極限承載力有很大提升。該新型基礎型式在某些特定地質復雜地區有著重要的實用價值,通過該種型式的樁基優化,使得樁基基礎既符合安全性又符合經濟性的要求。論文通過資料調研、對比、總結的方式界定了短樁的定義,并通過FLAC3D數值模擬軟件模擬了不同樁長(L=2m,3m,4m,4.5m,5m,5.5m,6m,7m,8m,9m,10m,11m)的單樁豎向承載力,當樁長L4m時,其承載力較低;當樁長為4m～6m時,較L4m時其承載力上升幅度較大,大概提高35%左右。而當樁長L6m時,其承載力并沒有顯著提升。綜上,本文界定了所討論的短樁為長度為4m≤L≤6m,且長徑比6L/D20的樁。系統分析了短樁與土共同作用的受力狀態,研究了承臺與地基土共同作用機理,通過FLAC3D數值模擬進行短樁承臺式基礎群樁模擬實驗,模擬了短樁不同樁長(L=4m、5m、6m),不同樁距(Sa=2d、3d、4d、6d)的短樁群樁承臺土反力的變化。得出承臺土反力與樁距成正比,當樁距Sa=4d～6d時,承臺土能充分發揮作用,承臺土反力基本不受樁長影響。承臺反力的數值最大處在邊柱內側附近,其次為承臺角點,再次為承臺邊緣處,群樁內部最小。為研究不同土層組合對短樁承臺式基礎的影響研究,進行在不同土層組合條件下短樁承臺群樁模擬實驗。測試包括不同承臺下土變化(粘土、砂土、圓礫土)、不同樁端土變化(粘土、砂土、圓礫土),分析土層變化對承臺分擔荷載比例及短樁承臺式基礎沉降量的影響,及二者之間的聯系。實驗得出,粘土層承臺分擔荷載比最大且沉降量最小。通過對不同土層組合Q-s曲線及承臺分擔荷載比曲線的分析比較,發現沉降量較小的土層組合承臺分擔荷載比較大�；谝陨涎芯砍晒�,本文認為短樁承臺式基礎應為淺基礎的優化型式,根據整體承載能力和沉降量雙重控制標準的設計原則,整體設計思路為:從天然地基設計出發,在滿足地基承載力的條件下,為了減少沉降而設置一定數量的短樁�；诖搜芯抗餐饔迷O(shè)計方法及關鍵數據取值,完成短樁-承臺-土共同作用設計流程。使用短樁-承臺-土共同作用設計方法對實際工程進行重新設計,并通過數值模擬軟件予以驗證。最后根據以上研究理論及短樁-承臺-土共同作用設計方法,使用VB6.0編程軟件完成"短樁承臺式基礎"設計程序的編制,使得該基礎型式的設計工程簡單高效,提高在實際工程中的應用效率。
[Abstract]:Short pile cap foundation is a new type of foundation which is excavated in the upper part and short pile in the lower part. In the process of pile foundation design, the pile foundation design is optimized by considering the reaction force of foundation soil under the pile cap, so that the ultimate bearing capacity of pile foundation can be greatly improved. This new type of foundation has important practical value in some special geological complex areas. Through the optimization of this type of pile foundation, the pile foundation not only meets the requirements of safety but also meets the requirements of economy. In this paper, the definition of short pile is defined by means of data investigation, comparison and summary, and the vertical bearing capacity of single pile with different pile lengths (L ~ (2) m ~ (3) ~ (3) m ~ (4) ~ (4.5) m ~ (5) ~ (5) m ~ (6) ~ (6) m ~ (?) ~ (8) m ~ (9) ~ (10) m ~ (11 m) is simulated by FLAC3D numerical simulation software. When the length of pile is L ~ (4) m, its bearing capacity is lower. Compared with L _ 4 m, the bearing capacity increases by about 35%. However, when the pile length is L6 m, the bearing capacity does not increase significantly. In summary, this paper defines the discussed short pile as a pile whose length is 4m 鈮，

本文編號：2274453