本文關鍵詞： Powerlink 工業以太網 實時性 集散控制系統　出處：《東華理工大學》2016年碩士論文　論文類型：學位論文

【摘要】：一直以來,現場總線技術廣泛應用于工業控制領域,但隨著工業自動化的發展,現場總線技術已經無法滿足工業控制過程中高速、高實時、強確定性、大容量數據傳輸?shù)男枨蟆９I(yè)以太網技術以其通信速率高、實時性強、確定性強、開放性好、資源共享能力強等特點在工業控制領域越來越受到關注。Powerlink憑借其實時性好、確定性強、協議開源、無需任何授權費用成為工業以太網的代表,在工業控制領域有著非常廣泛的應用前景。本文針對Powerlink實時以太網協議及應用進行深入分析,主要研究內容如下:(1)通過對Powerlink協議基礎知識的學習,為Powerlink協議的研究打下堅實的基礎。(2)Powerlink協議支持兩種工作模式,即基于請求/應答模式(PReq/PRes)和基于定時主動上報模式(PRC),本文對兩種模式的實現機制進行介紹,通過性能對比分析,得出兩種工作模式各自的優點和缺點,為不同的應用場合提供了選擇依據。(3)通過搭建Powerlink通信網絡,介紹Powerlink協議在Linux操作系統上的具體實現過程�；赪indows操作系統下進行主從站通信測試,使用Wireshark網絡診斷工具獲取網絡數據包,對數據包的內容進行分析。(4)將Powerlink協議應用于NT300集散控制系統,以解決網絡負載過重、實時性差的問題。介紹Powerlink協議的兩種網關設計方法,在此基礎上對集散控制系統的整體網絡架構進行設計。
[Abstract]:Field-bus technology has been widely used in industrial control field, but with the development of industrial automation, fieldbus technology has been unable to meet the high speed, high real-time and strong certainty in the industrial control process. Industrial Ethernet technology is characterized by its high communication rate, high real-time, strong certainty and good openness. Resource sharing ability has attracted more and more attention in the field of industrial control. Powerlink has the advantages of good real-time, strong certainty and open source protocol. As the representative of industrial Ethernet without any authorization fee, it has a very wide application prospect in the field of industrial control. In this paper, the protocol and application of Powerlink real-time Ethernet are deeply analyzed. The main research contents are as follows: 1) Learning the basic knowledge of Powerlink protocol. To lay a solid foundation for the research of Powerlink protocol. That is, based on the request / response mode PReq / PResand based on the timing of the active reporting mode, this paper introduces the implementation mechanism of the two modes, through performance comparison analysis. The advantages and disadvantages of the two working modes are obtained, which provide the basis for the selection of different applications. 3) through the establishment of Powerlink communication network. The implementation process of Powerlink protocol on Linux operating system is introduced. The master-slave communication test based on Windows operating system is carried out. Wireshark network diagnosis tool is used to obtain the network data packet, and the contents of the data packet are analyzed. 4) the Powerlink protocol is applied to the NT300 distributed control system. In order to solve the problem of overloaded network and poor real-time, two gateway design methods of Powerlink protocol are introduced, and the overall network architecture of distributed control system is designed on this basis.
【學位授予單位】：東華理工大學
【學位級別】：碩士
【學位授予年份】：2016
【分類號】：TP273;TP393.11

【參考文獻】

相關期刊論文 前10條

1 徐海亞;趙增基;朱波;李一石;孔祥善;;基于POWERLINK技術標準的交叉通信研究[J];控制工程;2015年S1期

2 連柯;;基于PowerLink的實時通信網設計[J];數字技術與應用;2014年11期

3 劉爭明;王欽若;萬振磊;;基于工業以太網Ethernet Powerlink和ARM9的伺服控制系統的設計[J];工業控制計算機;2011年04期

4 ;EUROMAP規范新增POWERLINK技術[J];自動化儀表;2010年09期

5 王維建;;工業以太網EtherCAT技術的原理及其實現[J];微計算機信息;2010年13期

6 ;POWERLINK正式列入IEC國際標準[J];軟件;2008年01期

7 馮海川;張承慧;崔納新;崔勝國;;Powerlink在紙機傳動控制系統中的應用[J];中國造紙;2007年01期

8 張士超;儀垂杰;郭健翔;林海波;劉尊民;周揚名;方玲;;集散控制系統的發展及應用現狀[J];微計算機信息;2007年01期

9 夏德海;現場總線技術講座——第二講 現場總線的國際標準[J];自動化與儀表;2005年04期

10 許洪華,劉科;確定性工業以太網Ethernet Powerlink[J];冶金自動化;2004年04期

，

本文編號：1447787